What are some common problems with blenders?

There are a variety of reasons why your blender might not be spinning, but the most common are:

Switch Is Failing

The first thing to check is the switch. Just because the blender started when you pressed the start button does not mean that the blades are actually spinning. Oftentimes, the blades will spin for a second or two when the blender is first plugged in, only to stop a few seconds later. This could be due to a faulty switch, which is the most common cause of blender failure. When the blender is plugged in, the two small metal prongs inside the switch are supposed to complete a circuit, sending electricity to the motor. If one of the prongs is broken or bent out of alignment, the circuit will not be completed. If your blender won’t turn on, the first thing you should do is check the switch.

Faulty motor

As with most appliances, a faulty motor is usually not covered by a warranty. Therefore, if your blender won’t spin and the blade is not damaged, you’ll need to purchase a new motor. Before you rush out and purchase a new motor, you should do a thorough inspection of the current motor. It may simply be clogged with food debris. To remove the motor, unplug the blender and remove the jar from the base. Wiggle the motor until it is loose and can be pulled out of the base. You can test the motor for functionality by plugging it into a wall socket. If it does not spin, it will need to be replaced. You can also use a toothpick or small wire to clean out any debris or food clogs that are in the motor.

The blade is damaged

Blender blades are extremely sharp and are used to chop through ice and frozen fruit, as well as other hard and frozen items. Therefore, it is not uncommon for the blades to become bent or torn after only a few uses. If your blade is damaged, it needs to be replaced. Do not attempt to straighten or repair the blades, as this could cause the motor to burn out. Instead, purchase a replacement blade and replace it. If you can’t find your blender’s model number, check the Internet for tips on how to identify it.

The blade is loose

Did you know that you can adjust the blades on most blenders? If the blades are too close to the walls of the jar, the food will not be properly blended. However, if the blades are too far away from the walls, the contents will splatter. To adjust the blades, simply loosen the socket holding the blade on the base of the blender jar and rotate the blade inward or outward. If the blade is not properly secured, it could be wiggling, causing the blender not to spin. To tighten the blade, simply turn the socket clockwise with a screwdriver until the blade is secure. If the blade is too loose and cannot be tightened, you’ll need to replace it.

The blade is not properly installed

If the blender is not spinning and you have checked the motor and the blades, you may have found that the problem is not with the blades themselves, but with the way they are installed. Most blenders have a small mark on the jar, indicating where the blade should be placed. If this is not the case, you may have installed the blades incorrectly. To properly install the blades, follow these instructions: – Unplug the blender. – Remove the jar from the blender and set it aside. – Remove the blade from the jar by gently pressing down on the blade and pulling it out of the jar. – Clean the jar and the blade with warm, soapy water. – Wipe the jar dry with a towel and set it aside. – Insert the blade into the jar and press down until the blade is firmly seated. – Replace the jar on the base and plug in the blender.

There is debris in the blade or seal

If the blender is not spinning and there is nothing wrong with the blade or the switch, it could mean that there is debris in the jar or seal that is preventing the blender from operating properly. The first thing that you should do is unplug the blender and remove the jar. With a paper towel or sponge, wipe out the inside of the jar to remove any food debris that may be trapped inside. Next, take a clean cloth and wipe down the jar seal and the outside of the jar. If there is still a problem, you may need to replace the seal.

Your jar is missing or damaged

If you have already checked the blade, switch, and the jar seal, but the blender is still not spinning, it could mean that your jar is either missing or damaged. To check if your jar is missing, open the blender jar and carefully examine all sides of the unit. If you can see a small nub where the jar should be, it may be missing, or it could be stuck in the lid or base. To see if the jar is damaged, run your fingers along the edge of the jar. If the jar is damaged or cracked, it will need to be replaced.

Your jar seal is damaged or perished

If you have checked the jar and found that it is not missing or damaged, the next step is to check the jar seal. If the seal is torn, perished, or cracked, you will need to replace it. The easiest way to test the seal is to plug in the blender and fill the jar with water. If the seal is damaged, the water will leak out. To test the seal, follow these steps: – Unplug the blender. – Remove the jar from the blender and set it aside. – Remove the blade from the jar by gently pressing down on the blade and pulling it out of the jar. – Clean the jar and the blade with warm, soapy water. – Wipe the jar dry with a towel and set it aside. – Fill the jar with water. – Plug in the blender and turn the switch to “on.” You may hear the blender struggle for a few seconds. – If the water is leaking from the jar, you need to replace the seal.

Blades Are Jammed

If the blender is not spinning and you have checked the motor and the blade, there may be something jammed between the blade and the jar. To check for a jam, unplug the blender, remove the jar, and poke your finger into the blade while rotating it. If something is stuck in the blade, you should be able to feel it. If so, carefully remove the item with a pair of tweezers.

Too Much Food

If everything seems to be in order with the blender, but it is not spinning, it could be due to too much food in the jar. Be sure to only fill the jar ¾ of the way full. Blenders are designed to chop and blend food items, not grind them into a pulp. If there is too much food in the jar, the blades will not be able to reach the center, causing the blender not to spin. What To Do When Your Blender Isn’t Spinning